On this page below you might get additional sensible advice in regards to Installing A Bathtub.
Installing a bath tub isn't precisely brain surgery, but it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably tough project. If the old tub is conveniently easily accessible, the project can move quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub and set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you might need an expert plumber to make tube links.
This article will certainly assist you install a brand-new tub in your washroom if you have actually currently gotten a new bathtub and don't require to alter the setup of your previous supply of water pipes.
Your tools and material list need to consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite troublesome because of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The previous kind needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub until the level reads degree.
To mount faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the supply of water and also check all joints and new pipework for leaks and tighten them if essential. Load the tub and additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the bathtub needs to wait until the tub has actually been used at the very least once as this will resolve it into its last setting.
Planning for the Setup
Firstly, the sustaining framework provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall surface between the bath and the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealer can crack fairly very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that editorial about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on another site. Sharing is good. You just don't know, you might be doing someone a favor. We take joy in reading our article about How to Install a Bathtub Yourself.
Comprehensive support here.